The transparent liquid rubber waterproof coating or clear waterproofing glue is an polymer containing prepolymer made of acrylic and other poly-addition reaction. It is formulated with catalysts, anhydrous additives, anhydrous fillers, solvents, etc. One-component acrylic waterproof coating.
Key Features
1. Single component, convenient to apply.
2. High cohesive force and ductility
3. Resistance to chemical corrosion, low temperature.
4. Anti-aging performance polymer sealant
5. Low VOC, Eco-friendly
2. High cohesive force and ductility
3. Resistance to chemical corrosion, low temperature.
4. Anti-aging performance polymer sealant
5. Low VOC, Eco-friendly
Usage method
Tools preparation: Clean tools including saw toothed plastic scraper, brush, plastic drum, 30kg electronic scale, rubber gloves and shovel knife.
Application environment requirement: sealant should be installed in the cleaning condition at 5~35℃ relative humidity 35~85%RH.
Cleaning substrates surface: Substrate should be solid without loose materials; Dry without construction on the wet substrates;
Clean without dust, oil, asphalt,tar, paint, wax,etc. It should be cleaned by wiping out,cutting, polishing, sweeping, washing, scrubbing and blowing.
The first coating application: First, brush the wall corner and pipe joints partly, then using saw toothed plastic scraper in large area. It should require homogeneous without too thick, the thickness of layer should be 0.55mm in general(If too thick,coating layer is easy to emerge bubbles)
The second coating application: After the fully curing of the first coating layer(about 12 hours), then knife-coating
homogeneously at the second time. The good thickness of the second coating is 0.7mm. The direction of knife-coating should be vertical with the first direction of knife-coating. Please refer to the first coating in details.
The third coating application: After the fully curing of the second coating layer, then knife-coating homogeneously at the third time. The direction of knife-coating should be vertical with the second direction of knife-coating. Special instruction: the three times of knife-coating should be confirmed based on thickness design of coating, the total coating thickness is 2.0~2.2mm.
Protective layer construction: If needed, protective layer can be applied on the surface of coating layer.
Cleaning tools: Dip the tools in methylbenzene or dimethylbenzene(prohibit it strictly to dip in ethyl alcohol solvent), the tools can be used after cleaning the solvent. If long time not be used, it should be washed by alcohol or other organic solvent. The curved sealant should be scraped and teared off.
Typical Applications
1. Bathroom floor, kitchen floor, balcony, roof, wall, etc.
2. Concrete floor to stop water leaking as waterproof layer.
3. Interior walls, toilet floor, basement.
4. Swimming pool waterproofing
1. Bathroom floor, kitchen floor, balcony, roof, wall, etc.
2. Concrete floor to stop water leaking as waterproof layer.
3. Interior walls, toilet floor, basement.
4. Swimming pool waterproofing
Technical Data Sheet
|
Usage
|
Appliance Paint, Boat Paint, Building Coating
|
|
Application Method
|
Spray,brush
|
|
Solid content
|
45%
|
|
Brand Name
|
Sinomaco
|
|
Model Number
|
GB/T16777-2008
|
|
Product Name
|
Transparent Waterproof Coating
|
|
Water resistance,96h
|
No whitening
|
|
Material
|
Co polymer blend, polyurethane, acrylic, epoxy
|
|
Surface drying time/h
|
4
|
|
Fully drying time/h
|
12
|
|
Tensile strength/Mpa
|
6.0
|
|
Elongation at break/%
|
150
|
|
PH
|
7
|
|
Tensile strength
|
1.6
|
